Put the wire cutter on the side, and then cuts through point of the scissors.
※ wire is not cut cleanly and not a special tool.

First crush the short side with the tip of the clamp, and then fixed (temporarily).

Clamped in place to fit the size of the caulking, you crush Omoikiri (tightening).

You crush the rest that could not be crushed at once (final blow).

This is not to exit in the other.

The most basic type. There are (katakuchi) mono thing is fixed and the diameter of the aperture, that is attached to both ends, and (both openings), which with only one side. Some have combined with the wrench and ratchet wrench. Like any place where it is hardly easy to use mail merge, and some are made to thin.

There is no opening, such as spanner, plug in type use like covering from the top of the bolt. Although it is not usually a wrench fit only from the direction 6, in the case of box-end wrench is a little more you have the flexibility handed. However, the space that is overlaid only from the top of the bolt is required.

Is the wrench can be used to change the size of the opening. This tool is useful, but how to keep a role of more than one book a wrench, you may also want to become loose or frustrated while working, you can no longer go into reverse.

Wrench for tightening or enamel, such as a screw cap and screw, or loosen. Some are made of "ball-point type (left photo)" to get the best into the. There have been attached and will also handle other things straight can be used in electric screwdriver or impact driver.

Is a wrench with a ratchet mechanism. Is more expensive than other wrench, but not need to unplug once Ichiichi After inserting is a great advantage. There is also a type of neck to bend as shown in the photograph.

Is the wrench handle and function with a ratchet mechanism, a combination of sockets that can be exchanged. Are often used in car and motorcycle maintenance, etc. Benefits of the socket wrench is the ability to loosen / tighten the head of the bolt, even if such penetrate as far as it will go like the wheel of the car.

Than the size of what you want to grab, to adjust the size of the mouth slightly smaller. The size of the mouth, adjust by turning the threaded portion at the tip of the handle.

The grip until you hear and write, "Kachin" In addition to grab what you want.

When you release the seized material is beyond easy to press the lever on the inside of the handle.

Into a very strong grip force so, would say if you do not want to damage the material and put a cloth or tape wrapped.

It is also useful if you get hot like material in the work, such as Thunder.

For example using the device. If you do not have confidence in the grip except in very severe in the hand will

Tighten by turning the black part of the pattern

To cut the pipe and repeat the "tighten-turn". To avoid straining the blade, let Tighten little by little.

Is a beautiful cross-section than the band saw and bow sawing.

Bali can be taken by filing that is attached to the cutter.

If you use off the blade is also stainless steel pipe stainless steel (sold separately). Whereas a normal blade is black, for stainless steel is a dark gray metallic color.

Cutting of wood, metal market: before and after use ¥ 700 (set of 5)

Normal for the saw blade does not cut yarn only in one direction, when the curve is cut there is a need to turn itself material or jigsaw. Thread of the spiral type saw blade so sharp in all directions against it, you can turn it off without changing the orientation of the blade and material. If you want to cut complex shapes can be very useful.

There are both for electric and manual for.

About ¥ 700 ~ ¥ 1,000: marking work rate applications: (needle exchange: approximately ¥ 500 ~ ¥ 1,000)

Of marking is usually made from steel of this has a pointed, pen-type is a thing to it. Also easy to store, you can also exchange needle like mechanical pencil, marking exactly so you can work fine earlier.

(¥ 1,000 before and after this one is M3 ~ M5) with screw diameter: Threaded rate processing applications:

You must tap the normal straight "cut, back" to repeat, in the spiral tap do not need that. If you want to use is often shortened to work most of the time, so thankfully there is also less effort.

A familiar person I've heard that some people would turn off the screws at once by using the electric drill, etc., but do not recommend the city.

How to Use Tap the dice here>

Around ¥ 3,000: Quotes Loosen / tighten the bolt Use:

Those with (※) ratchet wrench features a variable diameter added. Handy so you can respond easily to this one if every bolt. Or for a new product, there is a sense of still a little expensive.

※ The ability to lock either the forward / reverse ratchet function, and vice versa becomes free. Able to tighten or loosen the bolt simply repeat the reciprocating motion.

Around ¥ 500: heart rate out of material Application:

Determine the center of the material on hand tools. Equipped with guides to the front and back of 60 ° and 90 °, is a mechanism devoted to draw a line inside the material. If you draw a line position is about three Waridase a different angle.

Around ¥ 10,000: a fixed exchange rate of material application:

This tool is for advanced users, such as there is a drilling machine to the studio. So you can move the material in the direction of XY using the handle, the positioning device is easier than normal. There are several other devices with respect to, as well as cross-angle device was allowed to complex devices can be rotated 360 ° angle the device surface, the way them.

Rate of wood adhesion: applications by size (about ¥ 400 ~ ¥ 1,000)

American-made glue. It is suitable for your own speakers and furniture woodwork white bond, whereas commonly used in Japan to be rubber-like texture after drying, so here is completely cured. Is somewhat more expensive, is far from if you choose to use a reliable adhesive bond strength strongly, because the shorter drying time.

Around ¥ 1,000: base processing rate of pre-coating applications:

Are compatible with all paint materials as the base material before painting, fixing of paint is also high. You can also take advantage of the color of the material so transparent.

Material by size: the tension of the wire rate adjustment applications:

Is essential when you're trying to create tension in the wire and adjust the height and slope work and equipment hanging from the ceiling, was passed. For one screw has left-hand thread, making it the length of the entire mechanism is changed by turning the central part of the consolidation.

The size of the hole below, refer to "drill diameter for the hole" in the table below dimensions. When you do not know look at the nominal dimension is written in the tap itself, ー (screw diameter) (ex. M3 × 2.5mm hole under 0.5 = 3-0.5 =) even Waridaseru (pitch)

To handle the tap, fixed in a vice, such as material, to provide a cutting oil

Hang down into the hole a little below the cutting oil. Addressed to it at a right angle to the hole under the tap, turning two or three times while pressing to Kuitsuka

Work carefully so as not to tilt the tap handle. (Eliminating the clogging turn off the facet) Do not forget to return it if the tap straight 1/4 turn when rotated 3/4

(Better safe when you remove the handle has some missing) When you are finished threading, is drawn off the tap is rotated horizontally in a manner reverse to remove the screw

If the spiral tap, there is no need to screw off when "positive rotation 3/4, counter-rotating 1/4" round-trip. But somewhat more expensive, or if you want to increase the processing time can save a lot of work.

Vice such as a rod fixed to processing

Fixed to handle the dice, to provide a cutting oil

Rods hang down a little to the cutting oil. Directed perpendicular to the rods die, to turn two or three times while pressing Kuitsuka

Work carefully so as not to tilt handle dice. (Eliminating the clogging turn off the facet) Do not forget to return 1/4 turn when rotated 3/4

(Better safe when you remove the handle has some missing) Once you have threaded, pull a reverse die is rotated horizontally in a manner to remove the screw

How a combination of parts was produced by using a tap and die of this M5. Sweet precision in the vertical direction because it was produced in the thumb is understood. To higher precision machining is performed in conjunction with machine tool such as lathe.

Sandwiching the material in the beak of the larger

Open hole in the beak of the smaller

Measure on the opposite side of the beak

Slide the head of calipers to measure